RAGE AMPLIFIERS – INCREASED FORCE
Expanding our R line, The RAGE is now complemented with 3 new amplifiers. Each of these unique to their own, a 2.5 KW mono, the RAGE1200.6 – a 6 channel assymetrical compact amp & the even smaller RAGE600.4 – 600 watt 4 channel, which is narrower than a 1$ bill. These new designs & their small footprints leaves nothing spared. In fact, they have inherited features from the M and Zero series amplifiers. Low voltage indicators & clip sensors, on either the amp or the bass remote, is another new trait added to the Rage amplifiers.
The ACCU8 crossovers with designated frequencies on the potentiometers, makes it simple to tune your sound like a pro, but with less experience and tools needed. The RAGE600.4 and the RAGE1200.6 offer low, high & bandpass crossovers, making them more capable in sq systems where a more basic dsp can be used.
Compact power
13.7″ x 5.6″ (35 cm x 14.2 cm) is all it takes to house 1200 watts divided into 6 channels. Making it a perfect option for those wanting run a single amp for their entire system, maybe even a 3 way active front set in combination with a dedicated sub amp like the RAGE2500.1. The assymetrical configuration of the RAGE1200.6 is set up with ch 5 & ch 6 having twice the power of the remaining individual channels. Bridged you will see an excess of 600 watts, more than enough to power midwoofers and subwoofers in most cases.
If you have limited space for audio upgrades, the 600 watts out of the RAGE600.4 is the solution. The 9.5″ x 5.6″ (23 cm x 14.2 cm) footprint makes it ideal to use in bikes, boats & as a hideaway amp for a cleaner install. Clipping led, low voltage indicators & wide range ACCU8 crossovers with band pass configuration on all channels, sets the amp aside from the rest.
| SPECIFICATIONS | RAGE600.4 | RAGE1200.6 |
|---|---|---|
| Frequency Response: | 10 Hz ~ 25 KHz | 10 Hz ~ 25 KHz |
| Signal to Noise Ratio: | >90 dB | >90 dB |
| Input Sensitivity: | 6 V ~ 0.2 V | 6 V ~ 0.2 V |
| Crossover: | 24 dB / Oct | 24 dB / Oct |
| High Pass Crossover : | 20 Hz ~ 5 KHz | 50 Hz ~ 5 KHz (ch 1 ~ 4) 20 Hz ~ 200 Hz (ch 5 & 6) |
| Low Pass Crossover: | 50 Hz ~ 5 KHz | 50 Hz ~ 5 KHz (ch 1 ~ 4) 20 Hz ~ 200 Hz (ch 5 & 6) |
| Band Pass Crossover: | 50 Hz ~ 5 KHz | 20 Hz ~ 250 Hz (ch 5 & 6) |
| Bass Boost Frequency: | ||
| Damping Factor: | >250 | >250 |
| Power Terminal gauge: | 4 GA x 1 | 4 GA x 1 |
| Fuse Rating: | 60 A | 120 A |
| Operational voltage: | 9 V ~ 16 V | 9 V ~ 16 V |
| Dimensions: | 9" x 5.6" x 1.9" 23 x 14.2 x 4.9 cm | 13.7" x 5.6" x 1.9" 35 x 14.2 x 4.9 cm |
| Power @ 4 Ω 14.4v < 1% THD: | 4 x 100 w | 4 x 110 w + 2 x 200 (ch 5 & 6) |
| Power @ 2 Ω 14.4v < 1% THD: | 4 x 160 w | 4 x 160 w 2 + 2 x 320w (ch 5 & 6) |
| Power @ 4 Ω bridge 14.4v < 1% THD: | 2 x 320 w | 2 x 320 w + 1 x 640 w |
| Power @ 1 Ω 14.4v < 1% THD : |
*In order to get the full power output of the amplifier, it is crucial that your electical system is correctly (over) dimensioned. Failure to upgrading will constrain the power output & lower the efficiency. This can cause damage to the amplifier & void the warranty. Drivng the amplifier with ohm loads below of what is written in the manual is another void. Therefore take your time and read the manual thoroughly prior to installing! **Marine capable products are not to be subjected directly to water, but has the ability of being functional in humid conditions.