MA2000.1 Mean Mono
The new MA series, available in 4ch, 2ch and 1ch are already groud breakers.
The MA2000.1 is no exception. Offering all the features you would expect to see in higher end amplifiers, but the MA2000.1 does it with tiny dimensions.
It is still a big amplifier, but the narrow width and small height, makes it ideal to do stealth installs with. Which would be a shame,
given that all the MA series have backlit logos and terminals with LED.
2000.1 equals the max output at 1 ohm on 1 channel. With 2000 watts, the MA2000.1 will have no problem taking on any of our subwoofers up to the XM series.
Should it not be sufficient? Then the built in easy link mode allows you to strap 2 amplifiers into a single amp, providing up to 4000 watts.
More than enough to power any of our subwoofers.
16.53″ x 6.9″ x 1.96″ / 42 x 17.5 x 5 cm is all it takes to accomodate such power. A high efficiency circuit allows for the smaller and sleek heatsink design,
thus you won’t be hassled about not having sufficient space. The “ACCU8” crossovers gives you the ability to fine tune your amp like a pro.
With 41 clicks, each with corresponding frequencies per click, it takes away the doubt of where exactly the low pass or the subsonic is set.
MA Manual
MA Quick Specs
| SPECIFICATIONS | MA1000.4 | MA1000.2 | MA1200.1 | MA2000.1 | MA6000.1 |
|---|---|---|---|---|---|
| Frequency Response: | 10 Hz ~ 25 KHz (+/- 2 dB) | 10 Hz ~ 25 KHz (+/- 2 dB) | 15 Hz ~ 200 Hz (+/- 1 dB) | 15 Hz ~ 200 Hz (+/- 1 dB) | 10 Hz ~ 17.5 KHz |
| Signal to Noise Ratio: | >82 dB | >82 dB | >90 dB | >90 dB | >85 dB |
| Input Sensitivity: | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 6 V ~ 0.2 V |
| Crossover: | 24 dB / Oct | 24 dB / Oct | 12 dB / Oct | 12 dB / Oct | 24 dB / Oct |
| High Pass Crossover : | 15 Hz ~ 600 Hz 150 Hz ~ 6 KHz | 15 Hz ~ 600 Hz 150 Hz ~ 6 KHz | 15 Hz ~ 50 Hz (Subsonic) | 15 Hz ~ 50 Hz (Subsonic) | 10 Hz ~ 500 Hz |
| Low Pass Crossover: | 50 Hz ~ 4 KHz | 50 Hz ~ 4 KHz | 40 Hz ~ 180 Hz | 40 Hz ~ 180 Hz | 35 Hz ~ 17 KHz |
| Band Pass Crossover: | 15 Hz ~ 4 KHz | 15 Hz ~ 4 KHz | |||
| Bass Boost Frequency: | 30 Hz ~ 80 Hz / 0 ~ 12 dB | 30 Hz ~ 80 Hz / 0 ~ 12 dB | 30 Hz ~ 80 Hz / 0 ~ 9 dB | ||
| Damping Factor: | >250 | >250 | >250 | >250 | >300 |
| Power Terminal gauge: | 4 GA x 1 | 4 GA x 1 | 4 GA x 1 | 0 GA x 1 | 0 GA x 2 |
| Fuse Rating: | 105 A | 105 A | 120 A | 200 A | 500 A |
| Operational voltage: | 10 V ~ 15 V | 10 V ~ 15 V | 10 V ~ 15 V | 10 V ~ 15 V | 8.5 V ~ 16 V |
| Dimensions: | 11.69" x 6.9" x 1.96" 29.7 x 17.5 x 5 cm | 11.69" x 6.9" x 1.96" 29.7 x 17.5 x 5 cm | 12.2" x 6.9" x 1.96" 31 x 17.5 x 5 cm | 16.53" x 6.9" x 1.96" 42 x 17.5 x 5 cm | 22" x 10.23" x 2.44"56 c 56 x 26 x 6.2 cm |
| Power @ 4 Ω 14.4v < 1% THD: | 4 x 175 w | 2 x 350 w | 1 x 400 | 1 x 750 w | 1 x 1700 w |
| Power @ 2 Ω 14.4v < 1% THD: | 4 x 250 w | 2 x 500 w | 1 x 700 w | 1 x 1300 w | 1 x 3300 w |
| Power @ 4 Ω bridge 14.4v < 1% THD: | 2 x 500 w | 1 x 1000 w | |||
| Power @ 1 Ω 14.4v < 1% THD : | 1 x 1100 w / 1 x 1200 w (< 3% THD) | 1 x 2000 w | 1 x 6200 w (1 x 7500 w Competitors full bridge standard testing) |
*In order to get the full power output of the amplifier, it is crucial that your electical system is correctly (over) dimensioned. Failure to upgrading will constrain the power output & lower the efficiency which can cause damage to the amplifier & void the warranty.
This also includes ohm loads below of what is written in the manual. Do take your time and read the manual thoroughly prior to installing! **Marine capable products are not to be subjected directly to water, but has the ability of being functional in humid conditions.