MA1000.4 Beyond Belief
The new MA series, available in 4ch, 2ch and mono are already setting new standards.
Looks, performance, features, dimensions and marine capable* makes the MA series highly potent.
The 1000.4 refers to 1000 watts divided into 4 channels, making it a key component in any installation, either large or small.
With the ability to bridge the channels, the output is sufficient to forcefully drive our EL and IS subwoofers in addition to a set (or more) of speakers on the remaining 2 channels.
If the application is made for speakers only, 4 x 250 watt @ 2 ohm gives you sufficent headroom to add multiple speakers without lacking power.
The small footprint even makes it possible to install the amplifier in nearly any application. Efficiency is never a problem due to the full range class D design, fear not, it is still capable of SQL as we have used premium components in both pre and output stages in the amplifier.
Advanced crossovers with our “ACCU8” function (individal click position for corresponding frequencies), gone are the worries about how to adjust your amplifier best possible.
Impressive crossovers spannning all the way from 15 Hz to 6000 Hz, makes it possible to run tweeters directly of the MA1000.4,
however with the immense output better beware of the dangers it may present, both to your hearing and the tweeter itself.
In addition, the crossovers offers full range, highpass and lowpass on all channels and it even has bandpass for the more demanding end users.
In case of clipping or driving the amplifier beyond its limits, the built in clip function will automatically adjust the output till the signal is clean, which is way better than burnt voice coils.
Should your desire be powersports, atv’s or marine application, the MA1000.4 is marine capable**.
| SPECIFICATIONS | MA1000.4 | MA1000.2 | MA1200.1 | MA2000.1 | MA6000.1 |
|---|---|---|---|---|---|
| Frequency Response: | 10 Hz ~ 25 KHz (+/- 2 dB) | 10 Hz ~ 25 KHz (+/- 2 dB) | 15 Hz ~ 200 Hz (+/- 1 dB) | 15 Hz ~ 200 Hz (+/- 1 dB) | 10 Hz ~ 17.5 KHz |
| Signal to Noise Ratio: | >82 dB | >82 dB | >90 dB | >90 dB | >85 dB |
| Input Sensitivity: | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 4 V ~ 0.2 V | 6 V ~ 0.2 V |
| Crossover: | 24 dB / Oct | 24 dB / Oct | 12 dB / Oct | 12 dB / Oct | 24 dB / Oct |
| High Pass Crossover : | 15 Hz ~ 600 Hz 150 Hz ~ 6 KHz | 15 Hz ~ 600 Hz 150 Hz ~ 6 KHz | 15 Hz ~ 50 Hz (Subsonic) | 15 Hz ~ 50 Hz (Subsonic) | 10 Hz ~ 500 Hz |
| Low Pass Crossover: | 50 Hz ~ 4 KHz | 50 Hz ~ 4 KHz | 40 Hz ~ 180 Hz | 40 Hz ~ 180 Hz | 35 Hz ~ 17 KHz |
| Band Pass Crossover: | 15 Hz ~ 4 KHz | 15 Hz ~ 4 KHz | |||
| Bass Boost Frequency: | 30 Hz ~ 80 Hz / 0 ~ 12 dB | 30 Hz ~ 80 Hz / 0 ~ 12 dB | 30 Hz ~ 80 Hz / 0 ~ 9 dB | ||
| Damping Factor: | >250 | >250 | >250 | >250 | >300 |
| Power Terminal gauge: | 4 GA x 1 | 4 GA x 1 | 4 GA x 1 | 0 GA x 1 | 0 GA x 2 |
| Fuse Rating: | 105 A | 105 A | 120 A | 200 A | 500 A |
| Operational voltage: | 10 V ~ 15 V | 10 V ~ 15 V | 10 V ~ 15 V | 10 V ~ 15 V | 8.5 V ~ 16 V |
| Dimensions: | 11.69" x 6.9" x 1.96" 29.7 x 17.5 x 5 cm | 11.69" x 6.9" x 1.96" 29.7 x 17.5 x 5 cm | 12.2" x 6.9" x 1.96" 31 x 17.5 x 5 cm | 16.53" x 6.9" x 1.96" 42 x 17.5 x 5 cm | 22" x 10.23" x 2.44"56 c 56 x 26 x 6.2 cm |
| Power @ 4 Ω 14.4v < 1% THD: | 4 x 175 w | 2 x 350 w | 1 x 400 | 1 x 750 w | 1 x 1700 w |
| Power @ 2 Ω 14.4v < 1% THD: | 4 x 250 w | 2 x 500 w | 1 x 700 w | 1 x 1300 w | 1 x 3300 w |
| Power @ 4 Ω bridge 14.4v < 1% THD: | 2 x 500 w | 1 x 1000 w | |||
| Power @ 1 Ω 14.4v < 1% THD : | 1 x 1100 w / 1 x 1200 w (< 3% THD) | 1 x 2000 w | 1 x 6200 w (1 x 7500 w Competitors full bridge standard testing) |
*In order to get the full power output of the amplifier, it is crucial that your electical system is correctly (over) dimensioned. Failure to upgrading will constrain the power output & lower the efficiency which can cause damage to the amplifier & void the warranty. This also includes ohm loads below of what is written in the manual. Do take your time and read the manual thoroughly prior to installing!
**Marine capable products are not to be subjected directly to water, but has the ability of being functional in humid conditions.